Solar Tri-proof LED Tube Light Solar Batten Light with 8 Lighting Modes for Outdoor Parking Lot Bus Stop

Product Description

  Charging Indicator Light

          LED Indicator to show current battery level and charging status.

                                             ·    Green LED –    70% - 100% Charged

·    Yellow LED –   30% – 70% Charged

·    Red LED –        30% Charge or Less

·    Flashing LED of any color – Battery Charging 

   Please Note:
       The indicator will flash when charging, and when fully charged, it will display green.
      On/Off Switch - Will turn the Batten Light On and Off Manually. When using the remote control and the PIR Module, it must always be on.

Remote control instructions:

 Syncing the Remote Control to the Solar Light 

Syncing the Remote Control to the Solar Batten Light Find one end of the batten light, which is a control panel with a switch, and the indicator light should not be visible. Keep holding the MASTER ON button ("I" is ON "O" is OFF),and push the power button on the light head, continue to hold the MASTER ON button. The solar light head will light and flash gently three times indicating the program has been accepted Release the MASTER ON button. The light is now is standard mode and can now be turned ON/OFF with the MASTER "I" and "O" at the top of the remote and dimmed using the dimmer buttons. Now select a work mode from the below

Work Modes   The Solar Batten Light has 8 pre-programed work modes.  Mode Key     Mode Name                                   Running Mode       1 I       Mode  1  Light on 30% from dark to dawn.      2 I       Mode  2  Light on 50% for 8hrs, and then Light off.      3 I       Mode  3  Light on 80% for 4hrs, and then Light off.      4 I       Mode  4  Light on 100% for 2hrs, and then Light off.      1O Radar Sensor Mode1 Light on 100% for 3hrs, then to 0% until motion is detected, where the light will operate at 50%.      2O Radar Sensor Mode 2 Light on 100% for 3hrs, then to 5%, until motion is detected, where the light will operate at 50%.      3O Radar Sensor Mode 3 Light will not turn on unless motion is detected, where the light will operate at 100%.      4O      Mode RF returns remote to normal mode (as per left image)   Note:     1. Once a program mode is selected the Batten light cannot be turned ON/OFF or dimmed with        the Master button. Choose button '4O' (RF Mode) to revert to standard mode to control these              functions.     2. In this version, the remote control cannot control groups separately, and even if the remote        control mode (4O)is selected, it can only control all lights together.

Establish a local area network

    All lights installed at 50-100 meters will form a local area network. Each light is equivalent to a signal repeater in the network,
   so it can propagate the commands issued by the remote control one after another.
   When the 4O standard mode is selected, it will be able to control all lights synchronized with this remote control.

   

  Programme Clear 
     If you want to clear the programming of the remote control and lights to restore the factory settings. Please do the following.
        1. Turn on the light
        2.  Quickly press Master " I " key 5 times
        3. LED lights will blink 5 times which means that the Programme is cleared successfully.

Adjust the PIR Sensor Delay Timer 

The following instructions indicate how to adjust the amount of time the light will stay on when the PIR sensor is triggered when operating using any of the above-mentioned ‘PIR Modes’. The timer can be adjusted from 10-300 seconds. The default timer setting is 10 seconds. The light will constantly operate while the sensor is being triggered

1. On the sensor end of the tube, use your thumb to pull apart the buckles on both sides.

 2. Use a Phillips head screwdriver to turn the delay adjustment knob clockwise to the desired time.

Using your remote control 

The remote control has a range of 100-150m and can control more than one batten light when it is in remote control mode (4o).  

Product Detail

Installation Mode